Material : A Silicone

Time in mouth : Weeks/Months

Storage : Store at room temperature (15-25°C) (59-77°F) and out of direct sunlight.

Shelf life: 2 years from the date of manufacturev

• 1 x GC RELINE II CARTRIDGE 59g (48mL)
• 6 X MIXING TIP II L 
• 1 X GC RELINE II PRIMER FOR RESIN 8g (10mL)
• 1 X GC RELINE II REMOVER (FOR RESIN) 5g (5.5mL)
• 3 X DISPOSABLE BRUSH
• 1 x PLASTIC SPATULA
• 1 X GC RELINE II POINT FOR TRIMMING
• 1 X GC RELINE II WHEEL FOR FINISHING

DIRECT RELINING METHOD

• Check the resin denture for misfit and sensitive areas of the mucosa (e.g. with Fit Checker Advanced or Fit Checker Advanced Blue).
• Disinfect with a non-alcohol based product and dry the denture thoroughly. Relieve the area to be relined and roughen it, ideally by microabrasion.
• Clean in an ultrasonic cleaning machine containing an ultrasonic or enzymatic solution and dry thoroughly. Apply GC RELINE II PRIMER FOR RESIN to the bonding surface with a clean and dry brush and gently dry with clean, dry and oil-free air. Do not contaminate the surface with latex gloves, powder from gloves, etc.
  Note: Close the bottle with the cap immediately after use. Do not contaminate the primer bottle with moisture, in order to avoid that the primer liquid becomes blurry.
• Dispense GC RELINE II Soft, ExtraSoft or ExtraExtraSoft directly onto the denture. The working time is 2 minutes at room, temperature 23°C (73.4°F).
  Note: Do not apply a small amount of onset material (1-2 mm of mixed material) as this is slow to set and you will need to retain the denture in the mouth for over 5 minutes.
• Do not use a solvent like alcohol on the area between GC RELINE II and the denture as this will cause separation.
• Seat the denture in the mouth. Ask the patient to gently close into centric occlusion and then perform muscle trimming.
• Retain the denture in place for at least 5 minutes and remove it from the mouth.
• Using a scalpel or scissors, remove excess material on the edge of GC RELINE II Soft, ExtraSoft or ExtraExtraSoft.
• Using light pressure, progressively trim with GC RELINE II POINT FOR TRIMMING Using a speed of less than 20,000 RPM, and finish with GC RELINE II WHEEL FOR FINISHING using a speed of less than 6,000 RPM. Before use, the wheel must be set on a mandrel with a fixation cap or screw to hold it securely in place.
• If it is considered necessary to achieve an even smoother finish,follow the procedure below: (NB: GC RELINE II FINISHING MATERIAL A and B are sold separately)
• Apply GC RELINE II PRIMER FOR RESIN to the peripheral borders and margins of the denture in order to bond GC RELINE II FINISHING MATERIAL to it. Do not apply the primer to the
  relining material. Gently dry the primer (as in step 3 above).
• Dispense equal amounts of GC RELINE II FINISHING MATERIAL A and B onto the mixing pad. Mix with a plastic spatula and apply the mixture to the edge of the previously
  placed GC RELINE II Soft, ExtraSoft or ExtraExtraSoft material and to the denture using a sponge. The working time is 2 minutes and the setting time is 4 minutes at room temperature
  23°C (73.4°F). If it is necessary to check the fit of the relined denture, use an uncured fit checking material.

INDIRECT RELINING METHOD

• Proceed according to Steps No.1-4 for Direct Relining Method.
• Mount the denture on the gypsum model and press it on an articulator.
• Remove the denture from the model after about 30 minutes.
• If required, proceed according to Steps No.7- 8 for Direct Relining Method.